There are three Philips air fryer error codes, that you should know if you use this appliance. This appliance can make cooking fast and enjoyable, but when any one error code occurs, this probably prevents you from using it further.
However, all these error codes are simple to clear if the fix has been done correctly, and you can also fix them yourself when you know their cause and solution.
E1, E2, and E3 are common Philips air fryer error codes that you may encounter in your unit. We’ve gathered all the information regarding them in this guide including their causes and solutions.
Table of Contents
Below is the List of Philips Air Fryer Error Codes along with their Causes and Fix:
Philips air fryers are popular because of their look, effective working, and oil-free cooking abilities. However, if you’re seeing any code on the display of your device, this means there is a fault.
You will need to know the possible cause behind the displayed code and fix it according to its solution. In case your unit is new, you should contact support first to avoid voiding its warranty. If the unit is old, you should be aware of all errors’ causes and their fixes.
| Error Code | Possible Cause | Possible Solutions |
| E1 | the device was kept in an environment with a low temperature | Allow the device to adjust to room temperature for 15 minutes before plugging it in again to prevent E1 error on the display due to prolonged heat-up time. |
| E2 | a problem with the temperature sensor or heating element | Investing the issue manually, fix it according to required. |
| E3 | thermal safety mechanism has turned off the air fryer | Allow the oil or fat to cool before attempting to turn on the fryer again. |
What does E1 Error mean on Philips Air Fryer?
If you’re seeing an E1 error code on the display of your Philips Air Fryer, your unit is indicating a temperature sensor failure. This means your device was kept in an environment with a low temperature. This error is typically caused by the device being stored in a cold environment or subjected to a sudden change in temperature.
Solution:
Here’s how you can resolve the E1 Error by following these steps:
- Unplug your Air Fryer from the power source and let it cool down for at least 30 minutes.
- After 30 minutes, plug the air fryer back in and turn it on. If the error message disappears, good, the issue was likely caused by the device being stored in a cold and low-temperature environment.
- However, If the error message persists, you will need to replace the temperature sensor. It requires experience and knowledge to replace this component, So, Contact Philips customer service or a qualified technician for fixing the issue.
What does E2 Error mean on Philips Air Fryer?
The E2 error is a common error code in most Philips Air Fryer models. When this occurs, it typically indicates a problem with the temperature sensor. In simple words, The temperature sensor of the unit have malfunctioned or become disconnected. However, it is fixable.
Solution:
- First of all, Unplug your air fryer and allow it to cool down completely.
- Take a screwdriver and remove the upper panel. Now, locate the temperature sensor located near the heating element or on the side of the air fryer’s cooking chamber.
- Take a closer look and check the temperature sensor for any visible damage or signs of wear and tear. If it appears damaged, you will need to replace it.
- However, If the temperature sensor looks okay, use a multimeter to test it for continuity. Set the multimeter to the ohms setting and touch the probes to the two leads of the temperature sensor. The reading should be between 0 and 100 ohms. If the reading is outside of this range, the temperature sensor is faulty and needs to be replaced.
- Order a new temperature sensor for replacement from Philips or a reputable supplier. Always make sure to get the correct part for your specific air fryer model.
- Once you have the new temperature sensor, carefully disconnect the old one from the air fryer’s control board and remove it.
- Now, Install the new temperature sensor by connecting it to the control board and securing it in place.
- Take all opened parts closer, start reassembling the air fryer, and plug it back in.
NOTE: IN case you are not comfortable performing these steps yourself, consider taking your air fryer to a qualified technician for repair.
What does E3 Error mean on Philips Air Fryer?
The Philips Air Fryer E3 error typically indicates that the thermal safety mechanism has turned off the air fryer. Technically, This thermal safety mechanism is designed to prevent the air fryer from overheating and causing a potential safety hazard. It also means your unit’s internal parts are overheated and you need to cool down them and work on the cause.
Solution:
- Unplug the air fryer from the power outlet and allow it to cool down completely.
- Make sure that the air fryer is placed on a flat, stable surface and is not positioned near any flammable materials or sources of heat.
- Check the air fryer’s air intake and exhaust vents for any obstructions or blockages. Clear away any debris or obstructions that you find. Moreover, make sure the basket is not overfilled as it is another cause of the air fryer overheating issues.’’
- Now, Allow your air fryer to cool down for at least 30 minutes before attempting to use it again.
- Once you think your air fryer has cooled down, plug it back in and turn it on.
Conclusion
The Philips Air Fryer can display error codes E1, E2, and E3, which can indicate different issues with its components. However, understanding the cause and solution of each error code can help users troubleshoot issues and resolve them quickly.
Whether it’s an issue with the fan, temperature sensor, or thermal safety mechanism, following the appropriate steps described in this guide can help users get their air fryer up and running again.